The investigation of thin flash generation in a precision forging process of an aluminum long part using finite elements analysis (FEA) and corresponding forging trials is described in the presentation. Thin flash generation leads to bad handling and positioning in subsequent process steps and therefore tolerance defects. For investigation purpose, the forging processes were varied by use of different preforms with equal volumes but different mass distributions, while the geometrical parameters of the final part were not varied.
The forging processes were analyzed by FEA with focus on the value of the form-filling simultaneity depending on the preform geometry. Afterwards, corresponding forging trials were carried out for validation.The results of the experiments and the FEA showed good agreement concerning the part areas were thin flash generation was predicted by FEA and actually occurred in experiments.Preforms with higher values of form-filling simultaneity showed less thin flash generation while preforms with lower values of form-filling simultaneity showed significantly increased thin flash generation.
forging, aluminum, FEA, thin flash generation, prediction
In the automotive industry, aluminum forged parts must fulfill lightweight and heavy duty performance requirements. The generation of thin flash between die halves and in the small gaps between the die and punch must be prevented during the flashless forging process in completely enclosed dies. However, thin flash formation is neither predictable nor preventable.
A numerical model is developed based on finite element analysis to investigate and predict the generation of thin flash in aluminum flashless precision forging processes. The significance and effects of the main influencing input parameters, including billet temperature, forming velocity, and width of gap, on different resulting parameters are evaluated. Among all resulting parameters in the established numerical model, hydrostatic pressure and the forming force in the main forming direction have been identified as the most suitable for predicting thin flash generation.
aluminum forging, forging in completely enclosed dies, flashless forging, FEA
A low energy demand and a fast processing time are required in each industrial process for the production of crankshafts. Crankshafts have a very complex geometry and are forged with a high percentage of flash compared to other forging parts. Recent research showed the feasibility of a flashless forging of crankshafts. One way to forge a flashless crankshaft within three steps is to use cross wedge rolling, multi-directional forging and final forging.
This paper presents the investigation results of the influence of the cross section area reduction in cross wedge rolling on different parameters at multi-directional forging. First, the state of research, the process development and tool design of cross wedge rolling and multi-directional forging are described. Then a parameter study will be presented and the influence of the cross section area reduction on flash generation, billet temperatures, forming degree, forming forces and effective strain are shown. Generally, flash generates because a rotation-symmetric billet is forced into an asymmetric movement. The influence of an increasing cross section area reduction leads to a decreasing amount of flash at the bottom of the crankwebs.
multi-directional forging, cross wedge rolling, crankshaft, parameter study, forming angle
Most of today’s technical parts and components are made of monolithic materials. These mono-material components produced in established production processes reach their limits due to their respective material characteristics. Thus, a significant increase in production quality and efficiency can only be achieved by combining different materials in one part. Bulk forming of previously joined semi-finished products to net shape hybrid components that consist of two different materials is a promising method to produce parts with locally optimized characteristics. This new production process chain offers a number of advantages compared to conventional manufacturing technologies. Examples are the production of specific load-adapted forged parts with a high level of material utilization, an improvement of the joining zone caused by the following forming process and an easy to implement joining process due to the simple geometries of the semi-finished products.
This paper describes the production process of hybrid steel parts, produced by combining a plasma-transferred arc deposition welding process with a subsequent cross wedge rolling process. This innovative process chain enables the production of hybrid parts. To evaluate the developed process chain, coating thickness of the billet is analysed before and after cross wedge rolling. It could be shown, that the forming process leads to an improvement of the coating, meaning a more homogeneous distribution along the main axis.
process chain, plasma-transferred arc deposition welding, hybrid parts, cross wedge rolling
Hybrid forging combines forming of bulky and sheet metal elements in one process step. During the forming of the bulky and sheet metal elements a joining operation is initiated by the energy provided by the forging operation. Thereby component areas with high loads can be designed using a bulky element whereas areas with lower loads can be designed using a sheet metal element. In consequence, significant weight reductions as well as energy savings within the forging process are achievable. The paper presents the development of a hybrid forging process, using a control arm as demonstration part. By the aid of Finite Element Analysis computations the interactions between the main process parameters and the target value process quality are being derived. It will be shown that the bulky element’s shape has a major impact on further process parameters and that the temperature is crucial for material bonding.
FEA, hybrid forging, bulge forming, sheet metal forming
A low energy demand and a fast processing time are required in each industrial process for the production of crankshafts. Crankshafts have a very complex geometry and are forged with a high percentage of flash compared to other forging parts. Recent research showed the feasibility of a flashless forging of crankshafts. One way to forge a flashless crankshaft within three steps is to use cross wedge rolling, multi-directional forging and final forging.
This paper presents the investigation results of the influence of the forming angle in cross wedge rolling on different parameters at multi-directional forging. First the state of research, the process development and tool design of cross wedge rolling and multidirectional forging are described. Then the parameter study will be presented and the influence of the forming angle ? on flash generation, billet temperatures, forming degree, forming forces and effective strain are shown. Generally, flash generates because a rotation-symmetric billet is forced into an asymmetric movement. The influence of a rising forming angle leads to a higher amount of flash at the bottom of the crankwebs.
multi-directional forging, cross wedge rolling, crankshaft, parameter study, forming angle
To reduce production costs of forged parts, different approaches are possible. Especially for valuable materials like titanium, material costs represent a large part of the production costs. Therefore, reducing the initial material can decrease the total costs significantly. In order to identify the potential for improvements, an existing forging sequence was investigated.
For a titanium hip implant, a new forging sequence was developed. To reduce the initially needed material, cross wedge rolling as a preforming operation and die forging with flash brakes was investigated. The influence of the different stages on the final result was analysed and presented in detail. To increase the prediction accuracy of the newly developed flash-reduced forging sequence and to decrease iteration loops of die designs, feasible simulation parameters considering the boundary conditions of the forging environment were investigated. This is done using Finite Element Analysis (FEA), considering form filling, process stability, die stress and press forces. Using cross wedge rolling and die forging with flash brakes, the newly developed forging sequence reduces the flash rate significantly from 69 % to 32 %.
cross wedge rolling,forging, flash-reduced, finite element simulations, flash brakes
In multistage hot forging processes, the preform shape is the parameter mainly influencing the final forging result. Nevertheless, the design of multistage hot forging processes is still a trial and error process and, therefore, time consuming. The quality of developed forging sequences strongly depends on the engineer’s experience. To overcome these obstacles this paper presents an algorithm for solving the multi-objective optimization problem in designing preforms. Cross wedge rolled preforms were chosen as subject of investigation. An evolutionary algorithm is introduced to optimize the preform shape taking into account the mass distribution of the final part, the preform volume and the shape complexity. A crucial factor in preform optimization for hot forging processes is the amount of flash. Therefore, an equation for improving the amount of flash is derived. The developed algorithm is tested using two connecting rods with different shape complexities as demonstration parts.
preform optimization, forging, evolutionary algorithms, cross wedge rolling
In multistage hot forging processes, the preform shape is the parameter mainly influencing the final forging result. Nevertheless, the design of multistage hot forging processes is still a trial and error process and therefore time-consuming. The quality of developed forging sequences strongly depends on the engineer's experience. To overcome these obstacles, this paper presents an algorithm for solving the multi-objective optimization problem when designing preforms. Cross wedge rolled (CWR) preforms were chosen as subject of investigation. An evolutionary algorithm is introduced to optimize the preform shape taking into account the mass distribution of the final part, the preform volume and the shape complexity. The developed algorithm is tested using a connecting rod as a demonstration part. Based on finite element analysis, the implemented fitness function is evaluated, and thus the progressive optimization can be traced.
preforming optimization, hot forging, evolutionary algorithms, cross wedge rolling
Flash-reduced forging is a promising alternative for forging complicated high-duty parts. With a new process chain, the ability to reduce the existing flash quota of complex high-duty parts can make the difference in the competition and reduce the costs compared to flashless forging. The European Union is funding a research project which deals with the improvement of the forging sequence of a two-cylinder crankshaft by using flash-reduced forging. To increase the forecast quality of simulations using Finite-Element-Analysis for a future process chain design, the conventional existing process chain is simulated with FORGE3 and compared with industrial forging trials. Furthermore, a variation of simulation parameters has been used to get the significant influence parameters, fitting the results of these forging trials.
Forging, crankshaft, flash reduced, investigation simulation parameters
The most common method of bulk forming processes is closed die forging with flash. In these processes a surplus of material is used to ensure a complete filling of the cavity of the forging die. The surplus material is driven out of the die through the flash land, thus the design of the flash land has a major influence on the filling of the die. All dimensions of the flash land are typically fixed during the manufacturing process of the die and can not be changed within the forging process. By use of a moveable flash gap that can be actively changed during the forging process the material flow can be altered. This permits to improve the filling of the cavity. In this paper a moveable flash gap for a hot forging process is described and the influence of such a system on the filling of the die cavity is determined. This is done by a comparison to a conventional forging process with a fixed flash land. Furthermore, the results of experimental trials are compared to results of corresponding FEA simulations. Additionally, the influence of the initial billet temperature is investigated. Experimental trials showed that the moveable flash gap has a distinct influence on the material flow. The higher the flash ratio, the bigger is the influence of the moveable flash gap. The moveable flash gap is designed as a flash brake of a height of 2 mm. Its usage lead to differences in height of the parts up to 4.5 mm, which correspond to 16.6% of the parts height, compared to parts forged with a fixed flash land. If the forging temperature is decreased from 1200 °C to 1000 °C, the influence of the moveable flash gap is reduced. The average differences in height are about 0.5 mm (about 3%).
forging, die design, material flow, FEA, flash land, flash gap
The most common bulk forming process is closed die forging with flash. One goal of the industry is to reduce flash. For geometrically difficult parts like crankshafts flash reduction can be achieved by flashless preforming and flash-reduced final forging. The corresponding process design is challenging and defects like an insufficient cavity filling often occur in final forging. A controlled, moveable flash gap enables the alteration of the material flow, increasing the filling of the cavity again. In this paper, the flashless preforming for crankshafts and the influence of a controlled flash gap on cavity filling are described.
Forging, die design, material flow, FEA, flash land
In common forging processes for geometrically complicated parts such as crankshafts, an excess on material (flash) is technically needed to produce a good part, which results often in a material utilization between 60 % and 80 %. But the material costs in forging represent up to 50 % of the total production costs. By decreasing the flash ratio, the material usage and production costs in forging operations can be reduced significantly. For a crankshaft, the development of a new forging sequence was necessary, to achieve the reduction of flash. This development was performed for an industrial two-cylinder crankshaft, based on finite element analysis (FEA) simulations. The new forging sequence consists of three flashless preforming operations, an induction reheating followed by a multidirectional forging and the final forging. By use of this forging sequence the flash ratio was reduced from about 54 % to less than 10 %. Due to the huge reduction of the flash ratio, material as well as energy can be saved from now on, thus increasing the competitiveness of the company.
hot forging, FEA simulation, reduction of flash, multidirectional forging, resource efficiency
In this paper the comparison of simulations of cross wedge rolling processes with real trials using flat cross wedge tools is presented. The investigated materials are titanium and bainitic grade steel. First simulations were used to find the suitable parameter combinations for the investigated materials. Afterwards tools were manufactured with these parameters and additionally with some variations to investigate a field of parameters around this range of parameter values. The purpose of these tests is to find geometrical and process parameters with which a stable cross wedge rolling process for bainitic grade steel and titanium is possible.
cross wedge rolling, bainitic grade steel, titanium, finite element simulations
Reducing die wear is an effective way to decrease costs within bulk forming processes. Therefore, specific tool materials and heat treatments as well as special coatings are used to prolong the lifetime of the tools. Diamond-like carbon (DLC) coatings show high hardness and superior frictional behavior. However, these coatings seem to be inappropriate for hot forming due to degradation processes at elevated temperatures. But for warm forming, due to the lower temperature input into the cavity DLC might be an appropriate coating. Friction influences the shear stresses on the cavity surface and is therefore an important factor for reducing die wear. Hence, the frictional behavior of DLC coatings within warm forming will be analyzed within this paper by using the ring compression test. An amorphous hydrogenated carbon coating and six metallic doped amorphous hydrogenated carbon coatings (Cr, V and W each in two variants) are compared to CrN and no coating. Firstly, nomograms are graphed by the use of Finite-Element-Analysis. Thereafter two test series are carried out varying forming temperature and lubrication. The results show that DLC coatings with and without metallic doping are able to reduce friction in warm forming. Within the investigations an amorphous hydrogenated carbon doped with 15 % chromium shows the lowest friction factor and is able to reduce the friction factor compared to no coating by up to 64 % within warm forming.
diamond-like carbon (DLC), friction, warm forming, bulk forming, ring compression test
Preforming is an essential step in flashless forging processes. This paper describes the development of a four stage process chain for flashless forging of a crankshaft with pin and flange. The process consists of cross wedge rolling, lateral extrusion, bi-directional forging and final forming. The finite-element-analysis (FEA) performed with the software Forge 3 and experimental tests are executed with different process parameters, like billet and tool temperature, rolling velocity and steel. To reduce process steps, like lateral extrusion, a direct combination of cross wedge rolling and bidirectional forging is analysed with FEA-software Forge 3 for a one cylinder crankshaft without pin and flange. The results of the FEA give suitable forming angles alpha for cross wedge rolling and several geometric parameters for a modification of the bi-directional tool.
cross wedge rolling, bi-directional forging, crankshaft forging without flash, preforming
The range of structure sizes for industrial products produced today is increasingly expanding. This trend is evident in both small-scale (e.g. semiconductor applications) and large-scale (e.g. wind turbine rotors) products. While definitions already exist for smaller scale device structures, the conceptual distinction between conventional large products and large scale products is currently insufficient. In this study, we present a potential basis for the definition of large scale products. To achieve this, we derive hypotheses and examine these in the context of an empirical study using the examples of several sample products. It is shown that the transition from conventional products to large scale products is characterized by a disproportionate increase in product costs due to the augmentation of a characteristic product feature. Eventually we derive a proposed definition which characterizes large scale products in the field of production engineering.
xxl-product, large-scale, xxl, definition
Today most technical parts and components are made of monolithic materials. Nevertheless, the previously used monolithic materials reach their technological and constructive limits, so that an improvement of the component properties can be realized by hybrid parts. Forging of previously joined semi-finished products to net shape hybrid components is a promising method to produce functional adapted parts in a few process steps. This new process chain offers a number of advantages compared to other manufacturing technologies. Examples are the production of specific load-adapted forging parts with a high level of material utilization, an improvement of the joining zone caused by the followed forming process and an easy to implement joining process because of the simple geometries of the semi-finished products. This paper describes the production process of hybrid steel parts, which are produced by a combination of a deposition welding process with a subsequent hot forging (upsetting) or cross-wedge-rolling. It could be shown that the innovative process chain enables the production of hybrid parts whereby the forging processes lead to an improvement of the mechanical properties of the laser deposited material.
process chain, deposition welding, hot forging, cross-wedge-rolling
In this paper the development of the new production technology hybrid forging is described. Hybrid forging combines forming of bulk and sheet metal-elements including joining. Using three model experiments the joining by material bond and by form closure is analyzed. The form closure works like a riveting and the experiments showed good results. But not in every area of the specimen a material bond was present.
hybrid, forging, sheet metal forming, joining technology, steel, adhesive bond
Due to high mechanical loads the die cavity shows high wear in warm forging processes. Within this paper the ability of a hydrogenated amorphous carbon doped by 40 % chromium as wear protective coating for bulk forming processes will be analysed. Therefore billets with temperatures between 650 and 1200 °C have been forged on this layer. Thereafter the layers are analysed and the wear behaviour is evaluated.
coating, forging, forming
